AMD is a car door operator system which can be used for any kind of application: from residential buildings up to highly frequented office buildings and hotels. Due to the modular concept it is possible to optimally adapt the AMD system to the respective application. AMD - AMD Advanced Modular Door system. DOOR OPERATOR BOARD. Material group B72 - PCB assembly. Gross weight 0,75. ABOUT KONE PARTS. AMD is a car door operator system which can be used for any kind of application: from residential buildings up to highly frequented office buildings and hotels. Due to the modular concept it is possible to optimally adapt the AMD system to the respective application.
Sign in or Register
Product Details
Component Family Codes
- AMD - AMD Advanced Modular Door system
- ZZ-006 - PSR - Pre-defined packages
Product Description
- hu: AJTÓKÁRTYA-AMD2
- zf: AMD 門控制板
- de: ANTRIEBSEINHEIT AMD (D2)
- vi: Bo mạch điều khiển cửa cabin
- no: DØRKORT AMD DRIVE 2
- pt: DRIVE UNIT (D2)
- sl: EL. KARTICA POGONA KABINSKIH VRAT ZA AMD
- fi: ELECTRONIC BOX FOR AMD DRIVE 2
- sv: ELEKTRONIK BOX FÖR AMD DRIVE 2
- fr: MODULE ELECTRONIQUE OPE. AMD DRIVE 2
- it: MODULO PER PORTA AMD DRIVE 2
- es: MODULO PUERTA AMD DRIVE 2
- en: PCB,UNIT AMD DRIVE 2
- pl: Płyta napędu drzwi kabinowych
- ru: Печатная плата
- he: כולל קיט הסבה כרטיס מפעיל דלתות
- zh: 驱动单元（D2）
Material Utilisation Group
- 03177 - DOOR OPERATOR BOARD
Kone Amd Door Operator Manual Transfer Switch
Product Family Codes
- KONE 3000 MiniSpace
- KONE 3000 MonoSpace
- KONE 3000 TranSys
- KONE 3000S MiniSpace
- KONE 3000S MonoSpace
- KONE Alta
- KONE MiniSpace
- KONE MonoSpace
- KONE MonoSpace 700
- KONE MonoSpace Special
- KONE TranSys
- KONE 3000 MiniSpace
Unit of weight
kg
Hoping for some insight/suggestions.
Had an old AMD 2.0 board blow out capacitors. I replaced the board and now I can't seem to get this one to 'learn trip'. I have the manual for this board but everything I do referenced by the manual does not seem to work.
Here is what it is doing now:
•Test buttons work opposite, I need to hit close button to open and open to close. When I press the learn button twice the doors work properly on test, but will go back to reversed buttons after attempting 'learn trip'.
•When performing 'learn trip' the doors will automatically reopen after I run it close - is this normal?
•After cycling the doors about 2 times (the manual suggests no more than 5 cycles) on 'learn trip' the State light flashes as if there is a fault.
•The close end LED does not light up unless I press hard on the connector and even then it quickly turns off after trying to cycle the doors.
•When I think the doors have learned and place the car back on normal operation, the doors never open, but will sometimes answer hall calls.
•The doors will sometimes open very slowly and if the proximity edge beams are broken the doors will slam shut.
*note*
This is a 4-stop EC controller (I believe an older H-800 version) with a Kone AMD 2.0 door operator system. The proximity edge is wired separately to the COP and there is no mechanical safety edge.
I'm starting to believe the issue is due to a bad encoder. I've tried various dips witch configurations but nothing seems to work.
Any and all help is greatly appreciated
Had an old AMD 2.0 board blow out capacitors. I replaced the board and now I can't seem to get this one to 'learn trip'. I have the manual for this board but everything I do referenced by the manual does not seem to work.
Here is what it is doing now:
•Test buttons work opposite, I need to hit close button to open and open to close. When I press the learn button twice the doors work properly on test, but will go back to reversed buttons after attempting 'learn trip'.
•When performing 'learn trip' the doors will automatically reopen after I run it close - is this normal?
•After cycling the doors about 2 times (the manual suggests no more than 5 cycles) on 'learn trip' the State light flashes as if there is a fault.
•The close end LED does not light up unless I press hard on the connector and even then it quickly turns off after trying to cycle the doors.
•When I think the doors have learned and place the car back on normal operation, the doors never open, but will sometimes answer hall calls.
•The doors will sometimes open very slowly and if the proximity edge beams are broken the doors will slam shut.
*note*
This is a 4-stop EC controller (I believe an older H-800 version) with a Kone AMD 2.0 door operator system. The proximity edge is wired separately to the COP and there is no mechanical safety edge.
I'm starting to believe the issue is due to a bad encoder. I've tried various dips witch configurations but nothing seems to work.
Any and all help is greatly appreciated
Comments are closed.